Hyundai ix35 2011 Pin code Vvdi key tool Yes! Lonsdor k518 No! Xtool x100 No!

I have 3 key programming tools. Today, have tried all for Hyundai pin code reading. Attach all details below! Enjoy!
The car: Hyundai ix35 2011

The remote:

Key tools to have a try:
Xhorse vvdi key tool
Lonsdor K518ise
Xtool x100 pad 2
The test:
Test 1: Vvdi key tool reads pincode for Hyundai ix35: Success!
Step 1: detect the transponder
it’s id46 (hitag2)

Step 2: select data acquisition mode
here: use vvdi key tool and antenna

Put the key tool head antenna near the ignition coil and press OK to sniff data

Turn on ACC switch once with the car key
If it’s a smart key, remove the key battery first
Then put the key tool head antenna close to the switch

Insert the original key into the left coil and press OK to start the calculation
Don’t remove the key during calculation

Calculation success

Now pls click on “get more” to get pin codes
There are 2 options. Here, choose Hyundai password and get pin codes

Successfully get pin codes!
Ps. vvdi key tool has stopped production, vvdi mini key tool instead.
Test 2: Lonsdor k518ise reads pincodes for Hyundai ix35: Failed!

Tried again. Also failed!

Test 3: Xtool x100 pad2 reads pin code for Hyundai ix35: Failed!

Failed to communicate!
Conclusion:
Xhorse vvdi key tool (mini key tool) is the final winner. Worked well for Hyundai pin codes reading.

Comments

How to setup BMW ISTA/P Loader for ICOM A2 ENET cable K+DCAN adapter

The text here, as a user manual of BMW ISTA/P Loader / ICOM Emulator, is aimed to help those puzzled with ISTA/P Loader setup for ICOM A2 , ENET cable, K+DCAN USB interface. Note: all info here not original, shared by a forum member So try at your own risk! Main content: Part 1 – Compatible device Part 2 – Latest ISTA/P Loader update information Part 3 – How to install ISTA/P Loader v4.x Part 4 – How to use ISTA/P loader with ICOM A2, K+DCAN cable, ENET cable Part 5 – How to shut down ISTA/P Part 1 – Compatible device: ISTA/P Loader compatible with ICOM A2 (OEM or clone), K+DCAN USB and ENET Part 2 – Latest ISTA/P Loader update information: NEWEST – ISTA/P Loader V4.8 update info: Free download BMW ISTA-P Loader V4.8.7 to get all new info yourself …… ISTA/P Loader V4.2 update info: Custom resolution option added Improved detection of bmw scan tool ISTA-P install location. Improved compatibility with windows 10 Code...

JOHN DEERE DIAGNOSTIC OPTIONS

JOHN DEERE DIAGNOSTICS John Deere has recently been in the news because of their strict opposition to allowing farmers, equipment owners, and repair shops access to the information they need to repair and maintain their vehicles. If you read the main stream news, you would be left to believe that John Deere diagnostic with a computer is impossible. Well, we are here to help dispel that myth and give some more exposure to some tools that actually do perform diagnostics on John Deere. There are actually several solutions in the market, some of which we will cover in this post. JOHN DEERE EDL AND SERVICE ADVISOR The very best solution in the market is what the dealers use. John Deere dealers use a combination of PC-based computer with two critical components – John Deere Service Advisor software and the John Deere EDL v3 Adapter . The EDL v3 adapter looks like the picture shown below. It comes with a hard carry case, the adapter itself, a 9-pin connector, and the USB ca...

How to flash using a DoIP hardware

This is an Article showing just how simple it is to flash in DTS Monaco , over DoIP (Diagnostic over Internet Protocol). These newer units can ONLY be flashed over DoIP. Trying to flash them via CAN, will very likely brick your control unit, so that should not be attempted, under any circumstances! A DoIP hardware is required to flash these newer units. Such a hardware can be an SDConnect C4 DoIP , ECOM or VCX SE . DoIP brings signifficant advantage versus CAN, by that it is much faster (eg. flashing times take a few minutes, instead of several hours, telematics disks are not needed anymore, etc etc). Once you own the equipment, it will need to be correctly set up. There are online guides available, that show how to set up these devices. Following is the DTS Monaco guide on how to flash using a DoIP hardware! First, we’ll need to select the relevant SMR-D file, of the control unit, which we’ll be interacting with. Once interfacing with the control unit, before flash...

Automotive diagnostic tools

Search This Blog