Skip to main content

DoIP W222 Diagnosis SDconnect C4 Or Xentry Connect C5

 

What for Mercedes DoIP W222 diagnosis? Looking for a Mercedes diagnostic tool, supports W222 model new DoIT system with DoIP complaint…

You can have a SDconnect C4 (genuine better) or Xentry Connect C5 (clone or genuine..both ok)

SD connect C4 DoIP: you need rework

If you have an original SDconnect C4, you have luck with DoIP diagnosis.

If you have a clone SD connect C4, usually you fail to DoIP diagnosis and XENTRY will report an error message “Initialization of the multiplexer has failed” and fail to go further.

DoIP-W222-diagnosis-SDconnect-C4-or-Xentry-Connect-C5-1-3

But it doesn’t mean that you have no luck with DoIP.

Go for PCB rework…

The difference between DoIP and non-DoIP is pcb with Ethernet switch or not.

So, you have access to DoIP if you can solder the missing connector inside SDconnect.

You need: DoIP piggyback board, power board and new DoIP cable.

DoIP-W222-diagnosis-SDconnect-C4-or-Xentry-Connect-C5-2-3
DoIP-W222-diagnosis-SDconnect-C4-or-Xentry-Connect-C5-3-3
DoIP-W222-diagnosis-SDconnect-C4-or-Xentry-Connect-C5-4-3

Also, maybe you can convert TCp/IP DLL to DoIP (Ethernet) using some SD Connect PCB add-on and firmware update via SD slot! Display picture below. But it comes to taking risk if it is not well connected.

DoIP-W222-Diagnosis-SDconnect-C4-Or-Xentry-Connect-C5-5

Note that experienced tech is required to PCB rework; otherwise, you would damage your device- TRYING ON YOUR OWN RISK.

Xentry Connect C5 DoIP: 100% success.

With a XENTRY Connect C5, clone or original, you’ll have good success of DoIP diagnosis.

DoIP-W222-diagnosis-SDconnect-C4-or-Xentry-Connect-C5-6-3

Original XENTRY Connect C5 DoIP is the best choice to diagnose and program Mercedes newer models like W222.

DoIP-W222-diagnosis-SDconnect-C4-or-Xentry-Connect-C5-7-3
DoIP-W222-diagnosis-SDconnect-C4-or-Xentry-Connect-C5-8-3

Xentry Connect C5, 1:1 clone of the original, also works good with W222 DoIP diagnosis

DoIP-W222-diagnosis-SDconnect-C4-or-Xentry-Connect-C5-9-3

Note that this C5 must be the real version, not the fake one with boards same as SD Connect C4.

A real Xentry Connect C5 should have PCB as follows

DoIP-W222-diagnosis-SDconnect-C4-or-Xentry-Connect-C5-10-3
DoIP-W222-diagnosis-SDconnect-C4-or-Xentry-Connect-C5-11-3
DoIP-W222-diagnosis-SDconnect-C4-or-Xentry-Connect-C5-12-3
DoIP-W222-diagnosis-SDconnect-C4-or-Xentry-Connect-C5-13-3
DoIP-W222-diagnosis-SDconnect-C4-or-Xentry-Connect-C5-14-3


Comments

Popular posts from this blog

Xprog 6.12 5.84, 5.74, 5.60, 5.55, 5.51, 100% Works Software Free Download

Free download the newest Xprog V6.12 , XPROG 5.84 , XPROG 5.74 , XPROG 5.60 , Xprog 5.55 and XPROG 5.51. 1.XPROG-M 6.12 free download: Link 1: https://mega.nz/#!625RxAqJ!Y7IInI5ZhG3titLMPnFOvALbOa2RHIp7ENG2o4PIzag Password: No need Link 2: https://share.weiyun.com/5m5Vkw0 Password: fxo5qz Xprog 6.12 XPROG V6.12 installation video: XPROG-M V6.12 Using tips and installation guide: https://www.obd2tool.com/blog/2020/02/29/how-to-use-and-install-xprog-v6-12-on-win-xp-win7win8/ 2. XPROG V5.84 free download: https://mega.nz/#!7vpDwQ4D!MrdDW0tVf-6-wXtGKqpUmj7CA2HFlFlMf5AeNvYgRbI Tips for installing Xprog V5.84. 1.Disable anti-virus program when downloading software and running software. 2.Uninstall all the software and USB drivers of the old version xprog-box on your computer, then install the new XPROG5.84 software. 3.Run 5.84 Regsisty program for several timeswhen installing software 4.Run 5.84 Regsisty file for 2 times before you run software everytime . ...

Mercedes SCN coding service need help (Solved)

 scn coding meaning: Software Calibration Number coding, short for SCN coding is intrudes by Mercedes Benz around 2005. It replaced the previous coding technique with a centralized and almost automated technique to prevent incorrect coding being selected when replacing a module. scn coding service: Can be done online or offline mercedes scn coding software: You should have working XENTRY/DAS (crack ok). For old Mercedes (-2009), you should have software version 12.2016 or earlier: For new Mercedes (2009-2017), you should have software version 03.2017 or newer: scn coding calculator: Forget it if you find it on some forums. Usually it is a fake program, it will never calculate the SCN string. mercedes coding forum: https://mbworld.org/forums/ http://www.mbclub.co.uk/forums/ http://www.mercedescla.org/forum/ http://www.mbstartool.com/ Which version for Mercedes OFFLINE SCN coding? And which for ONLINE coding? For OFFLINE coding, you should have old versions befor...

How to Restore ICOM Next with All LEDs Red and System LED Blink Red/Yellow

  Problem with BMW ICOM Next : did an update on my motorcycle and everything went fine and today when I connect icom to OBD – all leds are just on with red color, system one is blinking red/yellow. Please do exactly as follow: 1. Disconnect the ICOM Next device from the power supply or vehicle. 2. Go to the directory C:\ProgramData\BMW\ISPI\data\TRIC\ICOMNext\ICOM-Image-xx-yy-zz. Note: This directory is hidden. Please see [?00045002EN]. 2.1. Copy the file ICOM_Next-rootfs-xxxxxx.tar.gz to the root directory of the USB flash drive. 2.2. Copy the file ICOM_Next-app-yyyyyy.tar.gz to the root directory of the USB flash drive. Note: – An ICOM_Restore.bin file is not available. Please use the files from the ICOM Next firmware package as described above. – xxxxxx and yyyyyy in the file names represent the version numbers of the respective files. – If the directory contains more than one ICOM-Image-xx-yy-zz folder, please choose the most recent one, i.e. the folder with high...