Skip to main content

Autel IM508/608 Program A New PCM on Honda Acura Guide

This article is about to show you how to program a new PCM for most Hondas and Acuras using Autel MaxiIM IM508/IM608.

The support list: https://www.autel.com/vehicle-coverage/coverage2

Here we have a Acura MDX 2005 to handle by the Autel IM508 Key Programmer.

This is the 3rd generation immobilizer, which is used on many Hondas like Accord or Acuras like TLX.

The car won’t start because of the new ECU in.

Autel-IM508-608-Program-A-New-PCM-on-Honda-Acura-Guide-1

We will reprogram it, so the key will work again.

Go to

IMMO>>Acura>>Automatic selection

Turn on the ignition so it will pull out the VIN.

Then go to

The 3rd mechanical key system>>Replace ECM/PCM

Autel-IM508-608-Program-A-New-PCM-on-Honda-Acura-Guide-2
Autel-IM508-608-Program-A-New-PCM-on-Honda-Acura-Guide-3

After about 5 minutes, we’ve registered the PCM.

Autel-IM508-608-Program-A-New-PCM-on-Honda-Acura-Guide-4

Meanwhile, the immobilizer light disappears.

Autel-IM508-608-Program-A-New-PCM-on-Honda-Acura-Guide-5

Turn off the ignition as required.

Follow instructions to check keys.

Autel-IM508-608-Program-A-New-PCM-on-Honda-Acura-Guide-6
Autel-IM508-608-Program-A-New-PCM-on-Honda-Acura-Guide-7
Autel-IM508-608-Program-A-New-PCM-on-Honda-Acura-Guide-8
Autel-IM508-608-Program-A-New-PCM-on-Honda-Acura-Guide-10

The car starts without any issues.

Autel-IM508-608-Program-A-New-PCM-on-Honda-Acura-Guide-9

Done! Nice and simple!

That’s the guide of programming a new PCM module using Autel IM508/Autel IM608.

This guide is from MODS FOREVER Team.

Any questions, contact us.

Labels:

Comments

Post a Comment

Popular posts from this blog

How to setup BMW ISTA/P Loader for ICOM A2 ENET cable K+DCAN adapter

The text here, as a user manual of BMW ISTA/P Loader / ICOM Emulator,  is aimed to help those puzzled with ISTA/P Loader setup for  ICOM A2 , ENET cable, K+DCAN  USB interface. Note: all info here not original, shared by a forum member So try at your own risk! Main content: Part 1 – Compatible device Part 2 – Latest ISTA/P Loader update information Part 3 – How to install ISTA/P Loader v4.x Part 4 – How to use  ISTA/P loader with ICOM A2, K+DCAN cable, ENET cable Part 5 – How to shut down ISTA/P Part 1 – Compatible device: ISTA/P Loader compatible with ICOM A2 (OEM or clone), K+DCAN USB and ENET   Part 2 – Latest ISTA/P Loader update information: NEWEST – ISTA/P Loader V4.8  update info: Free download BMW ISTA-P Loader V4.8.7 to get all new info yourself …… ISTA/P Loader V4.2 update info: Custom resolution option added Improved detection of bmw scan tool ISTA-P install location. Improved compatibility with windows 10 Code...
1 comment
Read more

JOHN DEERE DIAGNOSTIC OPTIONS

JOHN DEERE DIAGNOSTICS John Deere has recently been in the news because of their strict opposition to allowing farmers, equipment owners, and repair shops access to the information they need to repair and maintain their vehicles. If you read the main stream news, you would be left to believe that John Deere diagnostic with a computer is impossible. Well, we are here to help dispel that myth and give some more exposure to some tools that actually do perform diagnostics on John Deere. There are actually several solutions in the market, some of which we will cover in this post. JOHN DEERE EDL AND SERVICE ADVISOR The very best solution in the market is what the dealers use. John Deere dealers use a combination of PC-based computer with two critical components – John Deere Service Advisor software and the John Deere EDL v3 Adapter . The EDL v3 adapter looks like the picture shown below. It comes with a hard carry case, the adapter itself, a 9-pin connector, and the USB ca...
Post a Comment
Read more

How to flash using a DoIP hardware

  This is an Article showing just how simple it is to flash in DTS Monaco , over DoIP (Diagnostic over Internet Protocol). These newer units can ONLY be flashed over DoIP. Trying to flash them via CAN, will very likely brick your control unit, so that should not be attempted, under any circumstances! A DoIP hardware is required to flash these newer units. Such a hardware can be an SDConnect C4 DoIP , ECOM or VCX SE . DoIP brings signifficant advantage versus CAN, by that it is much faster (eg. flashing times take a few minutes, instead of several hours, telematics disks are not needed anymore, etc etc). Once you own the equipment, it will need to be correctly set up. There are online guides available, that show how to set up these devices. Following is the DTS Monaco guide on how to flash using a DoIP hardware! First, we’ll need to select the relevant SMR-D file, of the control unit, which we’ll be interacting with. Once interfacing with the control unit, before flash...
Post a Comment
Read more