Skip to main content

Clone PCM Reprogramming on 96 LT4 Corvette by GM Tech2

 

Works ok on my car 96 LT4 Corvette, You have to manually step through each test though. And you have to guess which standard your car is by manually trying each selection which is annoyingly slow to do. When you finally figure it out, then it goes faster.
Big thanks to @ grandspt for his experience sharing.

I purchased a 1996 PCM that was used for short money, my goal was to keep it as a spare for my ’96 LT4 Vette since parts are getting harder to come by.
I removed my PCM and installed this used PCM. I took out my GM Tech 2 Clone, opened my Windows XP Netbook that I had previously installed the TIS 2000 software (this software disk came with the Tech 2 Clone). I opened the TIS 2000 application and went to the “Service Program Application” and followed the steps to “Reprogram ECU”.
Now this used PCM obviously had a different VIN. So during the program when it prompted me to see if the VIN was correct I deleted the old VIN and entered in my cars VIN.
Then I uploaded the program for my VIN into the TECH2 Clone per the prompts, disconnected the Tech 2 Clone from my Netbook and connected my Tech 2 Clone to my OBDII port. I turned the ignition ON without starting the car and selected “Service Programming System” followed the prompts and watched the TECH 2 Clone load my VIN programming for my car.
It worked great, in fact I bought a second 1996 PCM for $150.00 and performed the same procedure and that one worked just as well!
After I used my JET DST to upload my Tune for my engine into the PCMs. The Tech II will obviously only install the factory calibrations. Now I have two spares in case my original fails.
Hope this information is helpful.

TIS2000 Application

Clone-PCM-Reprogramming-on-96-LT4-Corvette-by-GM-Tech2-1

Here is where you select Reprogram ECU.

Clone-PCM-Reprogramming-on-96-LT4-Corvette-by-GM-Tech2-2

These are the prompts for the Tech 2 setup.

Clone-PCM-Reprogramming-on-96-LT4-Corvette-by-GM-Tech2-3

First I only have a 1996 with the OBD II, this is all I could experiment with so I can’t check other years.
I think it can also work on the 94, 95 model years as well, but I could be wrong.
The TIS 2000 software comes with the Tech 2 scanner.

 

https://gmscantool.blogspot.com/2021/05/clone-pcm-reprogramming-on-96-lt4.html

Comments

Popular posts from this blog

Xprog 6.12 5.84, 5.74, 5.60, 5.55, 5.51, 100% Works Software Free Download

Free download the newest Xprog V6.12 , XPROG 5.84 , XPROG 5.74 , XPROG 5.60 , Xprog 5.55 and XPROG 5.51. 1.XPROG-M 6.12 free download: Link 1: https://mega.nz/#!625RxAqJ!Y7IInI5ZhG3titLMPnFOvALbOa2RHIp7ENG2o4PIzag Password: No need Link 2: https://share.weiyun.com/5m5Vkw0 Password: fxo5qz Xprog 6.12 XPROG V6.12 installation video: XPROG-M V6.12 Using tips and installation guide: https://www.obd2tool.com/blog/2020/02/29/how-to-use-and-install-xprog-v6-12-on-win-xp-win7win8/ 2. XPROG V5.84 free download: https://mega.nz/#!7vpDwQ4D!MrdDW0tVf-6-wXtGKqpUmj7CA2HFlFlMf5AeNvYgRbI Tips for installing Xprog V5.84. 1.Disable anti-virus program when downloading software and running software. 2.Uninstall all the software and USB drivers of the old version xprog-box on your computer, then install the new XPROG5.84 software. 3.Run 5.84 Regsisty program for several timeswhen installing software 4.Run 5.84 Regsisty file for 2 times before you run software everytime . ...

Mercedes SCN coding service need help (Solved)

 scn coding meaning: Software Calibration Number coding, short for SCN coding is intrudes by Mercedes Benz around 2005. It replaced the previous coding technique with a centralized and almost automated technique to prevent incorrect coding being selected when replacing a module. scn coding service: Can be done online or offline mercedes scn coding software: You should have working XENTRY/DAS (crack ok). For old Mercedes (-2009), you should have software version 12.2016 or earlier: For new Mercedes (2009-2017), you should have software version 03.2017 or newer: scn coding calculator: Forget it if you find it on some forums. Usually it is a fake program, it will never calculate the SCN string. mercedes coding forum: https://mbworld.org/forums/ http://www.mbclub.co.uk/forums/ http://www.mercedescla.org/forum/ http://www.mbstartool.com/ Which version for Mercedes OFFLINE SCN coding? And which for ONLINE coding? For OFFLINE coding, you should have old versions befor...

How to Restore ICOM Next with All LEDs Red and System LED Blink Red/Yellow

  Problem with BMW ICOM Next : did an update on my motorcycle and everything went fine and today when I connect icom to OBD – all leds are just on with red color, system one is blinking red/yellow. Please do exactly as follow: 1. Disconnect the ICOM Next device from the power supply or vehicle. 2. Go to the directory C:\ProgramData\BMW\ISPI\data\TRIC\ICOMNext\ICOM-Image-xx-yy-zz. Note: This directory is hidden. Please see [?00045002EN]. 2.1. Copy the file ICOM_Next-rootfs-xxxxxx.tar.gz to the root directory of the USB flash drive. 2.2. Copy the file ICOM_Next-app-yyyyyy.tar.gz to the root directory of the USB flash drive. Note: – An ICOM_Restore.bin file is not available. Please use the files from the ICOM Next firmware package as described above. – xxxxxx and yyyyyy in the file names represent the version numbers of the respective files. – If the directory contains more than one ICOM-Image-xx-yy-zz folder, please choose the most recent one, i.e. the folder with high...