Skip to main content

How to Setup Connection Between DTS Monaco and MB SD C4 DoIP

 

After Benz DTS Monaco Software installation,you need configure DTS Monaco for interface (here take MB SD C4 DoIP as example).So here Obd2tool.com show you guide on how to setup connection between DTS Monaco and MB SD C4 DoIP.

Preparations:

Benz DTS Monaco 8.16 8.08 Software Free Download

How to Install Mercedes Benz DTS Monaco 8.16 Software

Procedures:

After DTS Monaco installation,open network and sharing center

Click “Change adapter setting”

Right lick “Local Area Connection” and select “Properties”

Select “Internet Protocol Version 4 (TCP/IPv4)”—>”Properties”

Select “Use the following IP address”,and set address as below:

IP address:172.29.127.35

Subnet mask:255.255.255.0

Then click “Advanced…”

Click “Add”

Set address as below:

IP address:169.254.0.35

Subnet mask:255.255.0.0

Then click “Add”

Click “OK”

Click “OK”

And close

Now right click “Wireless Network”,then select “Properties”

Select “Internet Protocol Version 4 (TCP/IPv4)”—>”Properties”

Select “Use the following IP address”,and set address as below show

IP address:192.168.2.35

Subnet mask:255.255.255.0

Then click “OK”

Click “Close”

Now right click “SDconnect Toolkit” at lower right corner to select “Administration”

Click “Register/configure” option

It will show you the information as below.

Check off the “WLAN parameters,workshop” option

Select “Encryption” type to “WEP/Hex”

And set a Key:aaaaaaaaaaaaaaaaaaaaaaaaa

After then click “Start”

After finish it will show you a configuration information,close it.

And exit SDconnect Toolkit

Now you can run DTS Monaco with MB SD C4 DoIP.

Comments

Popular posts from this blog

Xprog 6.12 5.84, 5.74, 5.60, 5.55, 5.51, 100% Works Software Free Download

Free download the newest Xprog V6.12 , XPROG 5.84 , XPROG 5.74 , XPROG 5.60 , Xprog 5.55 and XPROG 5.51. 1.XPROG-M 6.12 free download: Link 1: https://mega.nz/#!625RxAqJ!Y7IInI5ZhG3titLMPnFOvALbOa2RHIp7ENG2o4PIzag Password: No need Link 2: https://share.weiyun.com/5m5Vkw0 Password: fxo5qz Xprog 6.12 XPROG V6.12 installation video: XPROG-M V6.12 Using tips and installation guide: https://www.obd2tool.com/blog/2020/02/29/how-to-use-and-install-xprog-v6-12-on-win-xp-win7win8/ 2. XPROG V5.84 free download: https://mega.nz/#!7vpDwQ4D!MrdDW0tVf-6-wXtGKqpUmj7CA2HFlFlMf5AeNvYgRbI Tips for installing Xprog V5.84. 1.Disable anti-virus program when downloading software and running software. 2.Uninstall all the software and USB drivers of the old version xprog-box on your computer, then install the new XPROG5.84 software. 3.Run 5.84 Regsisty program for several timeswhen installing software 4.Run 5.84 Regsisty file for 2 times before you run software everytime . ...

Mercedes SCN coding service need help (Solved)

 scn coding meaning: Software Calibration Number coding, short for SCN coding is intrudes by Mercedes Benz around 2005. It replaced the previous coding technique with a centralized and almost automated technique to prevent incorrect coding being selected when replacing a module. scn coding service: Can be done online or offline mercedes scn coding software: You should have working XENTRY/DAS (crack ok). For old Mercedes (-2009), you should have software version 12.2016 or earlier: For new Mercedes (2009-2017), you should have software version 03.2017 or newer: scn coding calculator: Forget it if you find it on some forums. Usually it is a fake program, it will never calculate the SCN string. mercedes coding forum: https://mbworld.org/forums/ http://www.mbclub.co.uk/forums/ http://www.mercedescla.org/forum/ http://www.mbstartool.com/ Which version for Mercedes OFFLINE SCN coding? And which for ONLINE coding? For OFFLINE coding, you should have old versions befor...

How to Restore ICOM Next with All LEDs Red and System LED Blink Red/Yellow

  Problem with BMW ICOM Next : did an update on my motorcycle and everything went fine and today when I connect icom to OBD – all leds are just on with red color, system one is blinking red/yellow. Please do exactly as follow: 1. Disconnect the ICOM Next device from the power supply or vehicle. 2. Go to the directory C:\ProgramData\BMW\ISPI\data\TRIC\ICOMNext\ICOM-Image-xx-yy-zz. Note: This directory is hidden. Please see [?00045002EN]. 2.1. Copy the file ICOM_Next-rootfs-xxxxxx.tar.gz to the root directory of the USB flash drive. 2.2. Copy the file ICOM_Next-app-yyyyyy.tar.gz to the root directory of the USB flash drive. Note: – An ICOM_Restore.bin file is not available. Please use the files from the ICOM Next firmware package as described above. – xxxxxx and yyyyyy in the file names represent the version numbers of the respective files. – If the directory contains more than one ICOM-Image-xx-yy-zz folder, please choose the most recent one, i.e. the folder with high...