VXDIAG Porsche PIWIS 3 Car List

Look here: Allscanner VXDIAG VCX DoIP Porsche Tester PIWIS 3 vehicle coverage
Compatibility:
Porsche from year 2005 to 2018, including post-2017 vehicles with DoIP protocol
Porsche 911(997) (991)
Boxster/Cayman (987)
Cayenne up to MY 2010
Cayenne from MY 2011
Panamera
Especially the latest models:
Paramera (971) 2018
Caynenne (92A) 2018
Macan (95B) 2018
911 (991) 2018
and other old models
Porsche Piwis3 Model Selection:
*Some other models can be selected only by connecting device with vehicle.
911:
992
992 Campaign
991
997
996
996 GT2
996 GT3
993, 964

Boxster:
982
981
987
986

Cayman:
982
981
987

Cayenne:
9YA
9YA Campaign
92A
9PA

Panamera:
971
970

Macan:
Macan

918 Spyder:
918 Spyder

Racing cars:
935
991 GT2 RS Clubsport
982 Cayman GT4 Clubsport
981 Cayman GT4 Clubsport

Miscellaneous:
Carrera GT
GT1
968
944
928

External components:

Porsche Piwis 3 Software:
Piwis III 38.300.030 – confirmed to work no issues
Diagnostic test: passed
Coding: passed
Programming: passed
VXDIAG Porsche Piwis 3 Instruction:
– Porsche Piwis 3 diagnosis + car list
– Porsche Piwis 3 Engineering
– Porsche Piwis 3 wiring diagram
– Porsche Piwis 3 remote help

Comments

How to setup BMW ISTA/P Loader for ICOM A2 ENET cable K+DCAN adapter

The text here, as a user manual of BMW ISTA/P Loader / ICOM Emulator, is aimed to help those puzzled with ISTA/P Loader setup for ICOM A2 , ENET cable, K+DCAN USB interface. Note: all info here not original, shared by a forum member So try at your own risk! Main content: Part 1 – Compatible device Part 2 – Latest ISTA/P Loader update information Part 3 – How to install ISTA/P Loader v4.x Part 4 – How to use ISTA/P loader with ICOM A2, K+DCAN cable, ENET cable Part 5 – How to shut down ISTA/P Part 1 – Compatible device: ISTA/P Loader compatible with ICOM A2 (OEM or clone), K+DCAN USB and ENET Part 2 – Latest ISTA/P Loader update information: NEWEST – ISTA/P Loader V4.8 update info: Free download BMW ISTA-P Loader V4.8.7 to get all new info yourself …… ISTA/P Loader V4.2 update info: Custom resolution option added Improved detection of bmw scan tool ISTA-P install location. Improved compatibility with windows 10 Code...

JOHN DEERE DIAGNOSTIC OPTIONS

JOHN DEERE DIAGNOSTICS John Deere has recently been in the news because of their strict opposition to allowing farmers, equipment owners, and repair shops access to the information they need to repair and maintain their vehicles. If you read the main stream news, you would be left to believe that John Deere diagnostic with a computer is impossible. Well, we are here to help dispel that myth and give some more exposure to some tools that actually do perform diagnostics on John Deere. There are actually several solutions in the market, some of which we will cover in this post. JOHN DEERE EDL AND SERVICE ADVISOR The very best solution in the market is what the dealers use. John Deere dealers use a combination of PC-based computer with two critical components – John Deere Service Advisor software and the John Deere EDL v3 Adapter . The EDL v3 adapter looks like the picture shown below. It comes with a hard carry case, the adapter itself, a 9-pin connector, and the USB ca...

How to flash using a DoIP hardware

This is an Article showing just how simple it is to flash in DTS Monaco , over DoIP (Diagnostic over Internet Protocol). These newer units can ONLY be flashed over DoIP. Trying to flash them via CAN, will very likely brick your control unit, so that should not be attempted, under any circumstances! A DoIP hardware is required to flash these newer units. Such a hardware can be an SDConnect C4 DoIP , ECOM or VCX SE . DoIP brings signifficant advantage versus CAN, by that it is much faster (eg. flashing times take a few minutes, instead of several hours, telematics disks are not needed anymore, etc etc). Once you own the equipment, it will need to be correctly set up. There are online guides available, that show how to set up these devices. Following is the DTS Monaco guide on how to flash using a DoIP hardware! First, we’ll need to select the relevant SMR-D file, of the control unit, which we’ll be interacting with. Once interfacing with the control unit, before flash...

Automotive diagnostic tools

Search This Blog