Car FANS C800 SCR Repair VS Adblue Emulator

Adblue Emulator is used for shield the SCR, the shielding method is any of the following pieces:
The urea pump does not work, the car does not burn urea, and the car has no limited twist.
The urea pump works normally, but the urea solution burns less.
The urea pump works normally, but regardless of whether the urea pump burns water or urea solution, the car will has no limited twist.
This is what Adblue Emulator used for.
Hazard of shielding urea:
Engine weakness
Urea pump damage
Injector blockage
Silencing catalyst sulfur poisoning
SCR system damage
Engine replacement (2980usd-7452usd)
Urea pump repair (745usd-1342usd)
Replace the injector: 45USD- 149USD
Silencing catalyst repair 1200USD-2232USD
SCR system replacement : 2976USD
Howe ever, CAR FANS C800 is for repairing the SCR instead of shielding it.
Here Carfans C800 SCR option:

Carfans C800 SCR types:

Comments

How to setup BMW ISTA/P Loader for ICOM A2 ENET cable K+DCAN adapter

The text here, as a user manual of BMW ISTA/P Loader / ICOM Emulator, is aimed to help those puzzled with ISTA/P Loader setup for ICOM A2 , ENET cable, K+DCAN USB interface. Note: all info here not original, shared by a forum member So try at your own risk! Main content: Part 1 – Compatible device Part 2 – Latest ISTA/P Loader update information Part 3 – How to install ISTA/P Loader v4.x Part 4 – How to use ISTA/P loader with ICOM A2, K+DCAN cable, ENET cable Part 5 – How to shut down ISTA/P Part 1 – Compatible device: ISTA/P Loader compatible with ICOM A2 (OEM or clone), K+DCAN USB and ENET Part 2 – Latest ISTA/P Loader update information: NEWEST – ISTA/P Loader V4.8 update info: Free download BMW ISTA-P Loader V4.8.7 to get all new info yourself …… ISTA/P Loader V4.2 update info: Custom resolution option added Improved detection of bmw scan tool ISTA-P install location. Improved compatibility with windows 10 Code...

PIWIS Tester Technical Information

WF51 – Re-coding Instrument Cluster (Workshop Campaign) Important: CRITICAL WARNING – This campaign includes steps where control unit(s) in the vehicle will be programmed with the PIWIS Tester. The vehicle voltage must be maintained between 13.5 volts and 14.5 volts during this programming. Failure to maintain this voltage could result in damaged control unit(s). Damage caused by inadequate voltage during programming is not a warrantable defect. The technician must verify the actual vehicle voltage in the PIWIS Tester before starting the campaign and also document the actual voltage on the repair order. Please refer to Equipment Information EQ1401 for a list of suitable battery chargers/power supplies which should be used to maintain vehicle voltage. Model Year: 2015 Vehicle Type: Cayenne S E-Hybrid (92A) Concerns: Instrument cluster Information: The instrument cluster on the affected vehiclesmay have been coded using an incorrect coding rule. As a result, there...

How to flash using a DoIP hardware

This is an Article showing just how simple it is to flash in DTS Monaco , over DoIP (Diagnostic over Internet Protocol). These newer units can ONLY be flashed over DoIP. Trying to flash them via CAN, will very likely brick your control unit, so that should not be attempted, under any circumstances! A DoIP hardware is required to flash these newer units. Such a hardware can be an SDConnect C4 DoIP , ECOM or VCX SE . DoIP brings signifficant advantage versus CAN, by that it is much faster (eg. flashing times take a few minutes, instead of several hours, telematics disks are not needed anymore, etc etc). Once you own the equipment, it will need to be correctly set up. There are online guides available, that show how to set up these devices. Following is the DTS Monaco guide on how to flash using a DoIP hardware! First, we’ll need to select the relevant SMR-D file, of the control unit, which we’ll be interacting with. Once interfacing with the control unit, before flash...

Automotive diagnostic tools

Search This Blog