Skip to main content

Some GM Tech 2 repair, how to reprogram any module using GM Tech 2


6-1
Hello!
Today I will briefly try to tell you about some possible problems and programming.
And so, if your Tech 2 worked fine, but then something went wrong, and there are some mistakes, then the first thing we need to do is to spend again testing of the device.
If you have the DLC 1, TPU, CCD, DLC2 – FAIL. Then just break the device and carefully solder all the chips that we see on the motherboard. If errors in a block VCI then take it, parse and also all propylaen. Only after all these manipulations, if you could not fix the error, then think about buying a new motherboard from www.obd2tool.com.

Now let’s talk about programming.
Here the opinions diverge. Someone said that you can perepisyvat using cheap Chinese card, someone says that it is necessary to use only original, in which there is an adapter for the write protection. If a cheap card flew off after the firmware, then try it again to overwrite soft but before writing be erased from it all.
Also there is a method of firmware as “cross-cutting”. In short, it means that the Tech 2 Scan Tool are connected to the machine and PC. And the management process itself goes through GlobalTIS.
May need the driver for PC saw the Tech 2, as a rule driver J2534.
All good and good luck in Your endeavors.
PS: In some laptops havent DB9 connector. Here you can just buy an adapter db9 to usb.
Labels:

Comments

Post a Comment

Popular posts from this blog

How to setup BMW ISTA/P Loader for ICOM A2 ENET cable K+DCAN adapter

The text here, as a user manual of BMW ISTA/P Loader / ICOM Emulator,  is aimed to help those puzzled with ISTA/P Loader setup for  ICOM A2 , ENET cable, K+DCAN  USB interface. Note: all info here not original, shared by a forum member So try at your own risk! Main content: Part 1 – Compatible device Part 2 – Latest ISTA/P Loader update information Part 3 – How to install ISTA/P Loader v4.x Part 4 – How to use  ISTA/P loader with ICOM A2, K+DCAN cable, ENET cable Part 5 – How to shut down ISTA/P Part 1 – Compatible device: ISTA/P Loader compatible with ICOM A2 (OEM or clone), K+DCAN USB and ENET   Part 2 – Latest ISTA/P Loader update information: NEWEST – ISTA/P Loader V4.8  update info: Free download BMW ISTA-P Loader V4.8.7 to get all new info yourself …… ISTA/P Loader V4.2 update info: Custom resolution option added Improved detection of bmw scan tool ISTA-P install location. Improved compatibility with windows 10 Code...
1 comment
Read more

JOHN DEERE DIAGNOSTIC OPTIONS

JOHN DEERE DIAGNOSTICS John Deere has recently been in the news because of their strict opposition to allowing farmers, equipment owners, and repair shops access to the information they need to repair and maintain their vehicles. If you read the main stream news, you would be left to believe that John Deere diagnostic with a computer is impossible. Well, we are here to help dispel that myth and give some more exposure to some tools that actually do perform diagnostics on John Deere. There are actually several solutions in the market, some of which we will cover in this post. JOHN DEERE EDL AND SERVICE ADVISOR The very best solution in the market is what the dealers use. John Deere dealers use a combination of PC-based computer with two critical components – John Deere Service Advisor software and the John Deere EDL v3 Adapter . The EDL v3 adapter looks like the picture shown below. It comes with a hard carry case, the adapter itself, a 9-pin connector, and the USB ca...
Post a Comment
Read more

Hyundai Automatic Transaxle-No Movement in Drive or Reverse Gear Repair

If you are servicing a vehicle with no movement in drive or reverse gear, follow the procedure shown below.And for more Hyundai projects,please check here:Hyundai Repair Cases REPAIR PROCEDURE: 1.Check for DTC in both the “Engine” and “Automatic Transaxle” menus: *   If DTC are found,you need repair it firstly. *   If no DTC are found, go to Step 2. 2.Remove the dipstick and check the ATF for a strong burnt smell. If the smell does not provide conclusive results, remove the oil pan and check for metal particles in the pan: *   If a strong burnt smell or metal particles are found, replace the transaxle *   If not, go to Step 3 NOTE: ATF that is a dark brown or black color does not indicate an internal transaxle concern;do not replace the transaxle. SPIII may change color to a dark brown after 10,000 to 25,000 miles in service. This change is normal for this type of ATF. VERIFY THE RANGE SWITCH ADJUSTMENT: 3.Move the shift lever to ...
Post a Comment
Read more