Automotive diagnostic tools

Super DSP3+ DSPIII Plus is 2019 New  Odometer Correction Tool update from DSP3 .Super DSP3+ mileage correction tool connect car via OBD2 directly. Super DSP3+ DSPIII Odometer Correction Tool Plus support 2010-2019 Years New Models. Bellow is the detail car list of Super DSP3+ DSPIII Plus V2019 New Odometer Correction Tool 2019 Version Super DSP3+ new upgraded cars Super DSP III Support Car List: AUDI/VW/ SKODA/SEAT/BENTLE/ LAND ROVER/ JAGUAR/ VOLVO/ PORSCHE Manufacture model  Version adapter activated AUDI  (NEC+24C64)06.2014-up  OBD adapter   yes A3   2014 NEC35XX VDO  OBD adapter   yes A4   13-up  OBD adapter   yes A5   13-up  OBD adapter   yes A6  12-up  OBD adapter  yes A6  12-UP(SMALL TFT) DIAG  OBD adapter  yes A7  10-up diag  OBD adapter   yes A8  10-up diag  OBD adapter   yes

Super DSP3  Odometer Correction Tool Super DSP3 Mileage Programmer fully supports newest high-end Car. Super DSPIII works for AUDI/VW/ SKODA/SEAT/BENTLE/MERCEDES/ JLR/ VOLVO/ PORSCHE 2010-2017 years of models Mileage Programming via OBD adapters. How to  correct odometer   with  DSP 3  via OBD adapters : Connect the OBD or other adapter with DSP3 Select Odometer Select a model to change km (Here: BMW) Choose 3 SERIES 2001-2003 Connect a proper adapter to the target odometer pcb power off Plug the proper adapter into the main hardware by the Adapter-Socket Load program and load OK Read and save current data Read KM, then change km Write km success! IMPORTANT NOTE 1:  DSP 3 Plus & BSI correction Before correction of some odometers, you have to reset BSI module first, such as ‘peugeot 307’, you should select ‘BSI’ and reset the km to zero, then adjust the km of odometer. IMPORTANT NOTE 2:  DSP III Plus &

Compared with X100 Pad2 , the X100 PAD2 PRO key programmer can support VW 4th & 5th IMMO by working with the KC100 adapter (included in the package). Here’s an example showing you how to use this tool to program keys for VW CC. Car Model: VW CC 2014 Device: Xtool X100 PAD2 PRO Procedures: Step 1: Read EEPROM chip. Step 2: Prepare two keys: an original one and a blank one. Step 3: Insert the original key to your car. Step 4: Touch X100 PAD2 shortcut on the device screen to start your key programming. Step 5: Select VW under Immobilization on the menu, then “4th/5th Immobilizer system” and touch “OK” to turn on ignition switch. Step 6: Choose “4th Immobilizer system” → “VW Passat/CC (recommend) ” → “Get PIN/CS “, where codes will be extracted from EEPRO chip dump file. Step 7: Now it’s back to the previous screen. Select “Generate 48 dealers key”, Step 8: CS code is needed here. Touch “OK”. Step 9: Put the blank key as shown in the imag

OBDSTAR X300 DP PLUS  is a new Android-based vehicle key programmer developed for internet applications. This article includes the reviews, FAQs and registration about this device. Part 1: Reviews about Obdstar x300 dp plus From rapidlocks: I bought one mainly for Honda , and it works great on Honda and not just for keys. I get a lot of calls for civics that have had flat batteries and been jump started which causes the immo and ecu to miss match, it’s great on fixing these too, so this was the main reason I bought it. It has some issues as do most cheaper machines, but has also had its uses too. It is good on later Fords after 2012, when other kits have failed this has saved the day. It’s excellent on Asian models as you would expect, honda, suzuki, toyota, etc, vag has improved alot and with the rfid ariel can do precoded cs after 2008 models. The android tablet is good quality and very simple to update. It is a good machine for its money especially if used on its