BMW FEM Mileage Reset Tool VVDI2 BMW Or Yanhua mini ACDP

Two BMW FEM mileage reset tools are using and verified working fine. They are VVDI2 BMW and Yanhua Mini ACDP and FEM Authorization.
Purpose: To reset mileage for F30 2014 FEM
Tool option:
Expensive one:
it’s very simple.
buying Xhorse vvdi2 for Odometer correction is quite expansive but for the FEM work this is one of the best and safest way so it’s worth to buy it.
and after that set 0 KM in FEM and change in cluster desire new KM
use vvdi 2 and follow the instruction for FEM.
Since Xhorse VVDI2 V4.3.0, it can reset FEM/BDC KM(cluster require reset manually).

For procedure, google and you will find articles.
Cheap one:
I can recommend to buy Yanhua mini ACDP and FEM Authorization
its a bit cheaper than VVDI2+Auth and never had any ISSUE doing FEM/BDC Mileage reset.
How to use Yanhua mini ACDP to reset BMW FEM odometer?

bmw-fem-mileage-reset-via-yanhua-acdp-10

Enjoy.

Comments

How to setup BMW ISTA/P Loader for ICOM A2 ENET cable K+DCAN adapter

The text here, as a user manual of BMW ISTA/P Loader / ICOM Emulator, is aimed to help those puzzled with ISTA/P Loader setup for ICOM A2 , ENET cable, K+DCAN USB interface. Note: all info here not original, shared by a forum member So try at your own risk! Main content: Part 1 – Compatible device Part 2 – Latest ISTA/P Loader update information Part 3 – How to install ISTA/P Loader v4.x Part 4 – How to use ISTA/P loader with ICOM A2, K+DCAN cable, ENET cable Part 5 – How to shut down ISTA/P Part 1 – Compatible device: ISTA/P Loader compatible with ICOM A2 (OEM or clone), K+DCAN USB and ENET Part 2 – Latest ISTA/P Loader update information: NEWEST – ISTA/P Loader V4.8 update info: Free download BMW ISTA-P Loader V4.8.7 to get all new info yourself …… ISTA/P Loader V4.2 update info: Custom resolution option added Improved detection of bmw scan tool ISTA-P install location. Improved compatibility with windows 10 Code...

JOHN DEERE DIAGNOSTIC OPTIONS

JOHN DEERE DIAGNOSTICS John Deere has recently been in the news because of their strict opposition to allowing farmers, equipment owners, and repair shops access to the information they need to repair and maintain their vehicles. If you read the main stream news, you would be left to believe that John Deere diagnostic with a computer is impossible. Well, we are here to help dispel that myth and give some more exposure to some tools that actually do perform diagnostics on John Deere. There are actually several solutions in the market, some of which we will cover in this post. JOHN DEERE EDL AND SERVICE ADVISOR The very best solution in the market is what the dealers use. John Deere dealers use a combination of PC-based computer with two critical components – John Deere Service Advisor software and the John Deere EDL v3 Adapter . The EDL v3 adapter looks like the picture shown below. It comes with a hard carry case, the adapter itself, a 9-pin connector, and the USB ca...

How to flash using a DoIP hardware

This is an Article showing just how simple it is to flash in DTS Monaco , over DoIP (Diagnostic over Internet Protocol). These newer units can ONLY be flashed over DoIP. Trying to flash them via CAN, will very likely brick your control unit, so that should not be attempted, under any circumstances! A DoIP hardware is required to flash these newer units. Such a hardware can be an SDConnect C4 DoIP , ECOM or VCX SE . DoIP brings signifficant advantage versus CAN, by that it is much faster (eg. flashing times take a few minutes, instead of several hours, telematics disks are not needed anymore, etc etc). Once you own the equipment, it will need to be correctly set up. There are online guides available, that show how to set up these devices. Following is the DTS Monaco guide on how to flash using a DoIP hardware! First, we’ll need to select the relevant SMR-D file, of the control unit, which we’ll be interacting with. Once interfacing with the control unit, before flash...

Automotive diagnostic tools

Search This Blog