If you want to fix your vehicles Chrysler, Dodge, Jeep and fiat problems. the wiTECH MicroPod 2 tool is your best choice.
witech micropod II newest software version is V17.04.27，
https://mega.nz/#!Nm5QRQYR!fVPAE7SNtYa2iE5eqQaZ1zyW7A1nh94-vPGpK1Iu3lg
witech micropod 2 only can work on XP computer system or windows 7 computer system.
when you install the witechmicropod 2 chrysler diagnostic tool , please notice:
1 installation AdobeAIRInstaller.exe
2 installation jre-6u45-windows-i586.exe
3 installation wiTECH_Install_17.04.27.exe
4. Restart the computer
warning:
1. The computer on the day of the date
2. The computer must be connected to the Internet
3. Connect the machine to the device to open the software
4. Tip registration, Turn off the software and turn it on Repeat several times You can use it normally
How to use witech micropod 2 for key programming ?
1 Plug the MicroPOD II device into the OBD port and connect the USB cable from the device to your laptop. This wakes the BUS on the car
2. Manually enter the VIN of the vehicle. This gives you access to the module list. Select the RFH (Radio Frequency Hub) module. This is the module where the key is registered
3. Next select “Miscellaneous Functions,” then “Program Ignition Fobix.” At this point, you are prompted to enter the VIN again, followed by the four-digit PIN Code.
4. After the four-digit pin is entered you are prompted to hit continue to “Program Ignition FOBIK.” Once you hit continue you must press the UNLOCK button on the FOBIX within 30 seconds (the FOBIX needs to be located near the center console during this procedure).
5. Programming of the Ignition FOBIX is now successful. The new key key is accepted into the car, and the ignition will now turn on and start the car. At this point, you also have the option to program a second key.
the chrysler key programmer wiTech MicroPod 2 picture as following:
witech micropod II newest software version is V17.04.27，
https://mega.nz/#!Nm5QRQYR!fVPAE7SNtYa2iE5eqQaZ1zyW7A1nh94-vPGpK1Iu3lg
witech micropod 2 only can work on XP computer system or windows 7 computer system.
when you install the witechmicropod 2 chrysler diagnostic tool , please notice:
1 installation AdobeAIRInstaller.exe
2 installation jre-6u45-windows-i586.exe
3 installation wiTECH_Install_17.04.27.exe
4. Restart the computer
warning:
1. The computer on the day of the date
2. The computer must be connected to the Internet
3. Connect the machine to the device to open the software
4. Tip registration, Turn off the software and turn it on Repeat several times You can use it normally
How to use witech micropod 2 for key programming ?
1 Plug the MicroPOD II device into the OBD port and connect the USB cable from the device to your laptop. This wakes the BUS on the car
2. Manually enter the VIN of the vehicle. This gives you access to the module list. Select the RFH (Radio Frequency Hub) module. This is the module where the key is registered
3. Next select “Miscellaneous Functions,” then “Program Ignition Fobix.” At this point, you are prompted to enter the VIN again, followed by the four-digit PIN Code.
4. After the four-digit pin is entered you are prompted to hit continue to “Program Ignition FOBIK.” Once you hit continue you must press the UNLOCK button on the FOBIX within 30 seconds (the FOBIX needs to be located near the center console during this procedure).
5. Programming of the Ignition FOBIX is now successful. The new key key is accepted into the car, and the ignition will now turn on and start the car. At this point, you also have the option to program a second key.
the chrysler key programmer wiTech MicroPod 2 picture as following:
Comments
Post a Comment